Pay in installments of $1283.25 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 22 - Jul 27
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Carli 4.5" Unchained 3.0 Bypass Suspension System 11-16 Ford 6.7L PowerstrokeThe Unchained is a purpose built kit. 3. 0" 2 Tube Front Kings and 4 Tube Bypass rear 3. 0" shocks are paired with fabricated coil buckets, 4. 5" lift multi rate coil springs and Full Leafs in the rear for unsurpassed off road capability from a bolt on suspension system. A roll cage should be considered at this level of suspension. If you're looking for the best on road ride offered by Carli with a huge boost in off road capability, grab a Dominator.
The Unchained is a purpose built kit. 3.0" 2-Tube Front Kings and 4-Tube Bypass rear 3.0" shocks are paired with fabricated coil buckets, 4.5" lift multi-rate coil springs and Full Leafs in the rear for unsurpassed off-road capability from a bolt-on suspension system. A roll cage should be considered at this level of suspension.
If you're looking for the best on road ride offered by Carli with a huge boost in off-road capability, grab a Dominator. If you're after a suspension that will allow more off-road performance than the chassis to which it's bolted, this is your huckleberry. With the Unchained Suspension System, Carli recommends a roll cage and axle truss. This system is far more capable off-road than even the Coilover-Bypass System.
CARLI UNCHAINED SUSPENSION SYSTEM COMPONENTS
The truck will sit 4.5" higher in the front and have more wheel travel thanks to the taller, Progressive Rate Coil Springs that mount into the Fabricated Carli Spring Buckets. Radius Arm Drop Brackets reset the pivot point and keep the travel linear for the best ride while Sway Bar Drop Brackets reset the sway bar engagement point. The included Bump Stop Drops protect the shocks from over-compressing while the Adjustable Track Bar centers the front axle and Stainless Brake Lines firm up braking and ensure there is enough line for the newfound travel. To round off the front end, you'll also receive Caster Shims to tighten the steering.
REAR LEAF SPRINGS
The rear is outfitted with a Full Progressive Spring Pack requiring no block to achieve proper ride height; thus, travel is extended and wheel hop/axle wrap minimized at the cost of 15% less load capacity than a stock F-250. If capacity is a concern, upgrade with Long Travel Airbags to restore the payload capacity to that of a SRW F-350.
FULL PROGRESSIVE LEAF SPRING KIT SPECIFICATIONS:This System has been optimized for use with the Full Progressive Leaf Springs. This system is also compatible with the Progressive Add-a-Packs but there will be a notable ride quality difference on and off-road. Selecting "NO Rear Leaf Spring Selection" will result in an unknown ride quality and height result as all Carli Systems are optimized to Progressive Leaf Springs.
- Block eliminating
- Light 3/4 ton capacity, full capacity attainable with long travel airbags
- Includes new u-bolts and rear bump stop drops
- Provides a 1" rear high stance on matching 4.5" suspension systems
- 3.5" axle tube
CARLI TUNED KING 3.0" BYPASS SHOCKS
This system boasts Carli Signature tuned, King 3.0" 2-Tube Front and 4-Tube Rear Piggy-Back Bypass Shocks so large, Carli needed to fabricate custom mounts to fit them; as the old adage goes, there's no replacement for displacement. The 3.0" shock has a piston surface area 45% greater than a 2.5" King and 126% larger than a factory 2.0" shock making it far more efficient in all situations. Additionally, as explained above, they've added bypass tubes to this pinnacle off-road system. The massive surface area and bypass tubes ensure you'll achieve unmatched off-road performance while receiving a civil controlled on-road ride. To fit these shocks, included are fabricated mounts that lift the upper mounting point and position the shock away from the frame while the standard bump stop extensions were shortened to allow for more up-travel to compliment the additional down-travel from the longer shock. In an effort to provide you with the best product, Carli designed a custom piston to determine proper base flow rates to ensure the shock works well in the heavy duty truck platform; the shocks were then tuned based on seat-of-the-pants feel. ALL of Carli's King shocks are rounded off with shafts machined and polished from a solid piece of 17-4 Stainless. Unlike King's standard shafts, there is no coating to wear off, weather is far less likely to hurt them and if there is a small chip, you can round the edges with emery cloth to ensure the seal housing isn't damaged as they're not brittle like the stock, hardened shafts. The shocks are finished with King oil good to -55° F. Note that all King shocks are built with a plated steel body. If subjected to inclement weather for extended periods, Carli recommends wrapping your shocks in 3M to provide a moisture barrier that's replaceable.
WHEEL AND TIRE FITMENT
As with the Coilover Bypass, it's recommended that users purchase a Differential Guard for axle protection, High Mount Steering Stabilizer to keep the steering as controlled as the suspension and Fabricated Radius Arms for strength and Limit Strap mounting. Again, at this level of suspension, a roll cage and axle truss is also recommended if the system will be used to its full off-road potential. On the 4.5" Bypass equipped Ford Systems, Carli recommends 17"-18" wheels, no more than 9" wide with 4.5"-5" of backspacing with a 37", E-Rated Tire. The more rubber, the better the small bump compliance will be at proper inflation pressures. The ride will firm up as you go larger in wheel diameter.
IMPORTANT NOTES:- WHEELS: Carli Recommends a 17"-18" Wheel, no more than 9" wide with 5" of Backspacing on 4.5" Lift Systems.
- TIRES: 37", E-Rated Tire Fitment is Recommended. Recommended unloaded Tire Pressure 45F/40R
- RECOMMENDED CONFIGURATION: Carli 4.5" Systems are Designed and Tested on Vehicles with 17"-18" Wheels with 37", E-Rated Tires. Stock wheels and tires or running a larger wheel diameter will result in a stiffer ride.
- REAR DRIVESHAFT Trucks equipped with a 2 piece driveshaft will require CS-CARRIERDROP-F to ensure proper driveline angles.
- Diesel Power Products and Carli strongly suggest the use of either options available. These options are designed to work flawlessly with the rest of your kit and, are the best way to go. However, we understand you may already have the necessary provisions and/or products to use with this kit so we give you the option to not include any leaf spring provisions.
- Diesel Power Products and Carli strongly suggest the use of either options available. These options are designed to work flawlessly with the rest of your kit and, are the best way to go. However, we understand you may already have the necessary provisions and/or products to use with this kit so we give you the option to not include any sway bar drop or Torsion Sway Bar provisions.
OPTIONAL CARLI ADD ON COMPONENTS
LEAF SPRING SHACKLE SPECIFICATIONS:Much of the jarring ride of the Super Duty rear can be attributed to the factory vulcanized bushings in the leaf spring pack and shackle. The factory shackle is very strong BUT the design is not conducive to a smooth ride. The Carli shackle is constructed of 1/4″ American cold-rolled steel. The mid-length gusset ensures no deflection while the serviceable bushings offer a far superior ride to the bind of the factory bushings.
- Greasable and rebuildable
- Far better ride than factory shackle
- 1/4" steel construction
- Fits factory and Carli springs
Icing on the cake, these arms add Additional Tire Clearance, Limit Strap Protection for your Front Shocks, 1/4" Boxed Steel Constructions, Serviceable 17-4 Stainless Spherical Bearings and Adjustable Caster Correction up to 3.5° over stock specs to leave Death-Wobble in the rear-view.
- 1-4 degrees of adjustable caster correction
- 3/16 construction, fully internal gusseted with 1/2" additional tire clearance
- Limit straps kit included
- Serviceable 17-4 stainless spherical joint at frame connection for longevity and bind free cycling
Bolt in replacement for the factory stabilizer. Adjustable from 70-200 psi to run neutral (no directional influence at 70psi) or at 200psi to counter the right-hand pull inherent to tires like Toyo Mud Terrains.
- Stainless Steel
- Bolt-in replacement for OEM stabilizer
- Works on leveled and lifted trucks ONLY
- Will NOT work with dropped pitman arms
Bolt in steering stabilizer which compliments a Carli, or factory, high mount stabilizer. Adjustable from 70-200 psi to run neutral (no directional influence at 70psi) or at 200psi to counter the left-hand pull inherent to tires like Nitto Trail Grapplers. Run in conjunction with the Carli High Mount for the ultimate Dual, Opposing Steering Stabilizer combination that's infinitely adjustable.
- Custom valved for larger tires, adjustable nitrogen pressure
- Includes differential guard and clamp
- Combines with high-mount stabilizer for opposing setup
- Optimized for Carli 2.5-5.5" systems
It's recommend to add this to shim to ALL 2-piece driveshafts (CCLB) to shim the Carrier bearing down alleviating the angle of all joints. If your truck is equipped with a single piece driveshaft, this will not fit and is not required.
- Drops carrier bearing on 2-piece driveshafts
- Prevents take-off shudder / driveline vibration
- Stackable 3/8" shims for 1-4" rear lift
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy