Pay in installments of $3.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 31 - Aug 5
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Sarracenia, 3.5in, Purpurea Venosa RedSarracenia purpurea venosa commonly known as the purple pitcher plant, has wide, stocky , bulbous traps that are green with red veins, and a tint of pink or peach color. If you need any more photos or additional information on this product, send us a message using the chat button on our website with the product name, and we will get back to you as soon as possible. This plant has a representative product photo and the item you will receive may not be
Sarracenia purpurea venosa commonly known as the purple pitcher plant, has wide, stocky , bulbous traps that are green with red veins, and a tint of pink or peach color.If you need any more photos or additional information on this product, send us a message using the chat button on our website with the product name, and we will get back to you as soon as possible.
This plant has a representative product photo and the item you will receive may not be exactly as shown.
Attributes
Type: Carnivorous, Tropical, HouseplantHeight: 4in - 8in
Spread: 6in - 10in
Light: Full to Partial Sun / Bright to Partial Bright Light
Water: Moderate with purified water
Zone: 7-9
Pet Safe: Non-Toxic
Care
General Maintenance: Be careful with your pitcher plant, they are sensitive to rough touch. Feed with a few live or dead insects once every couple of weeksTemperature: -5 degrees Celcius to 28 degrees Celcius, it is best to not let them freeze, the pitchers may die but the rhimozone should survive short amount of time frozen
Light: These plants will thrive outdoors in the warm season in full sun. Bring indoors for a dormancy period. Bright indirect light will work as well, but they are best suited to outdoor locations
Watering: Water only with the purest water you have available. Rainwater or reverse osmosis water are best. If using bottled water, make sure there is no salt. If using tap water, allow to sit for a minimum of 24 hours to evaporate any chlorine and sterilizing agents.
Fertilizer: To fertilize any carnivorous plant, you feed them insects. With pitcher plants just drop live or dead insects into the pitchers. DO NOT FERTILIZE THE SOIL this will cause chemical burns and kill your plant.
Soil: Open, wet and boggy, but can tolerate more sandy soil. Main thing with any carnivorous plant is to give them the poorest soil possible. They will thrive in a mixture of pebbles and peat moss. Too rich of soil will cause
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.3 ★★★★★
Based on 8 reviews
Sort
Product Reviews
★★★★★ 5
Excellent Tool For Drilling Shelf Pin Holes
I had a project where I was extending the depth of the bottom half of a bookcase I had made out of pre-drilled MDF from Home Depot. The original bookcase was 11" deep x 10' high. The extended depth of the bottom is to be used to hold audio gear and needed to be 18" depth, front to rear. I was able to increase the depth but had to insert additional panels on the left and right so that shelf pins could be installed. I needed a shelf pin jig to do that, and this jig was perfect for the job.
After completing my holes and mounting some shelves I was pleased that the alignment with the inner portion of the shelf was perfect and the distance between holes lined up exactly as with the original panels from Home Depot.
The jig is high quality fabricated aluminum, not plastic, and it comes with two drill bits, and stop and Allen wrench, including an instruction manual, all in an attractive plastic case.
The jig is well worth the modest price and I would definitely recommend it for drilling shelf clip holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 27, 2024
★★★★★ 5
a solid choice
I realized I don't need to drill 5mm holes, so this item is just perfect. It's higher quality than those other cheap-chinese noname jigs. In particular:
* The stop collar provided actually fits the drill bit. I had one from Tanyo that had too-big collars that didn't stay put.
* The fence pins are very soilid, so the jig doesn't move while in place. Other brands have a long knurled screw that wobbles and allows the kiig to move around.
* The plate is thick, making it feel sturdy.
* It's phyically smaller than the others, because it doesn't have any useless features like euro-hinge hole guides. The case is more compact and stores well.
Overall, very satisfied with this jig.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 3, 2026
★★★★★ 5
Great product
Great well made product and nice case. Works great for 1/4” holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 15, 2026
★★★★★ 5
A solid and easy to use product.
Worked like a charm. It is extremely durable and easy to use. I bought this item because the one I wanted wasn’t available. I don’t regret getting it.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 22, 2026
★★★★★ 5
very nice tool
likes, all aluminum construction, seems very accurate and uses more sturdy 1/4 inch shelf pins instead of the 5mm ones
comes with 2 bits which is a huge plus the competition makes you buy the 1/4 drill and only is set up for 5mm to start.
this jig will work along side, for now, my other jig
dislike is the fact it only has 1/4 pin capability not a deal killer in any way, and it has "pins" to support the jig on the edge again this is both an advantage and disadvantage as you can change the depth of where the pins are located BUT if you are making something smaller the jig may not calibrate consistently.
on another positive you can replace the bits easily and commonly as they are not proprietary and simply standard 1/4 inch bits
this will be a fine addition to my other goingmake tools and future ones
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 3, 2025